Replies: 8 (Who?), Viewed: 765 times.
Mad Poster
Original Poster
#1 Old 28th Aug 2020 at 6:42 PM
Default Bone Assignments
If you have a mesh and an alpha mesh. Is there a way to copy the bone assignments from one to the same area on the other? I have an alpha skirt I had to pull down and now the bones don't match the body underneath.
Advertisement
Mad Poster
#2 Old 28th Aug 2020 at 8:04 PM
For small edits you can mark and copy from other areas with the buttons in the Joints menu. Make sure you do it properly for left, right and middle.

(Blanking on the button names atm, and can't check - I think it is copy and assign, but not sure).
Mad Poster
Original Poster
#3 Old 20th Sep 2020 at 5:29 PM
Yikes. Not had a reply for three weeks. Is that how long I've been struggling with it? DX

Does anyone know how I can make the front of the dress flatten while sitting? I've been poking the bone assignments for ages and nothing has worked.
Screenshots
Mad Poster
#4 Old 21st Sep 2020 at 12:19 AM
Make sure you've properly assigned the lower parts in the front to either move with the thighs or bend with the knees, depending on where the parts are, and that you blend the weights and don't go from 100% thighs to 100% calves, because then you get bad-looking bendy bits.

Dresses, especially ones with a lot of things going on in the skirt, tend to be in the category of outfits that just don't do what you want them to do however long you poke at them. The wider or messier the skirt is, the less likely it's going to bow down for tables and other things that are in the way of it.

Using ANIM mode in Milkshape (pose mode) can sometimes help when you're testing out bone assignments - saves you from going in and out of the game to test the skirt a hundred and umpteen times. Make sure to save a copy of the file before you turn it on, because you can end up messing up the skeleton.
Mad Poster
Original Poster
#5 Old 23rd Sep 2020 at 11:46 AM
Yeah It's really annoying, because the lower parts have the same bones as the thighs, but don't move the same way as the thighs. It's driving me nuts. DX
Mad Poster
#6 Old 23rd Sep 2020 at 4:24 PM
Probably because of the bend in the knees - it does look like a section is going up when it should be going down, but it could be something else. It's difficult to say without looking at the bone assignments.

For pants you have 100% thighs above the knees, then 50/50 thighs-calves in the midpoint of the knees, 100% calves below the knees. Skirts can vary a bit, because these also have to take into account the midpoint between the L/R sections, so they're usually gradient in the horizontal axis, too (something like 25/25 L/R thighs and 25/25 L/R calves for the knees for the midpoint, but could vary a great deal).
Mad Poster
Original Poster
#7 Old 23rd Sep 2020 at 4:38 PM
Skirt is 100% thighs. Doesn't go beneath the knees.
Lab Assistant
#8 Old 23rd Sep 2020 at 7:53 PM
Basic question, but how does the dress look in T pose/Bodyshop? Like Simmer22 said, there's only so much you can do for a wide skirt. Here's what I could get from an edited Maxis mesh.

From what I can see, the transition between the pelvis and the thighs is really sudden. I think smoothing it out would help a lot already. For the petals' tips, perhaps a touch of weight from the calves might help? Even if they're above the knee, they'd benefit from being 'pulled down'. I'd try something like this. .

Useful Maxis meshes to reference: Glamour Life's DressPuffSkirt and Celebration's DressWeddingShort.

I'm http://crispsandkerosene.tumblr.com/ on tumblr, admittedly not very active on MTS.
Mad Poster
Original Poster
#9 Old 25th Sep 2020 at 6:55 PM
In T pose it looks fine. It's only once they start moving around.

However, I think I've got it to a point where it's tolerable. I lack the skills to get it perfect. I tried weighting the bottom as calves, but it dragged the petals down strangely.

I attached the joints in Milkshape, if anyone has any ideas for improvement. The skirt doesn't respond well to complicated stuff like joints that share two different parts e.g. thighs/knees. Well not with my lack of skill at it, at least. XD
Screenshots
Back to top